Automotive

dsr1apartcatalog2015000.jpg
dsr1catalog000small.jpg dsr1action2015000small.jpg dsr1alonecatalog000small.jpg dsr1action001small.jpg dsr1rbcatalogsmall.jpg

TurboXTools™ DSR Door Skin Remover Attachment C

Use the power assistance of your drill to remove damaged door skins of passenger vehicles and light trucks.  No more dust, dirt or sparks from time consuming grinding.  And no risk of burn marks on the door frame!  This Malco TurboXTools solution cuts the damaged door skin off the door frame!   The model DSR1 Door Skin Remover inserts into the chuck of a minimum 14.4 Volt cordless or maximum 7 Amp corded drill.  A telescoping clamp adjusts to fit length and width of any drill housing for easy one hand operation.  Optional spacers are stored on clamp for large motor housings.  The clamp collar allows the shear head to be rotated 360° and set in any position for optimum tool clearance when navigating profiles or to facilitate easy material flow.  A narrow working head, with spacer guide, cuts through the rounded edge of the door hem.  Lateral adjustability of the cutting blades ensures optimal performance in 20 to 22 gauge (0.91 to 0.76 mm) automotive steel.  Simply point the blades into the hem to start the cut.   The serrated upper blade bites onto the two layers of metal without slipping.  Turning the  tool, with the spacer guide flush against the hem, allows the tool to cut off a narrow strip along the hem edge.  The Malco Door Skin Remover also navigates over mild body lines and around corners to finish the job.  Long lasting, hardened shearing blades ensure long service life.  Blades are also easily replaceable and are available as a set with a factory installed spacer guide.

 

 

Malco Tool Talk Article

Made In USA

Specs

Catalog # Description Max. Hemming Capacity ga.(mm) Min. Hemming Capacity ga.(mm) Attachment Weight lb(kg)
DSR1 Door Skin Remover, Drill Attachment 20 (0.91) 22 (0.76) 2.2 (1.00)
DSR1RB Replacement Blade Set with Spacer -- -- --

Drill Requirements: Min 1/4 in (6.35mm) Chuck, Min 14.4 V-DC/Max 7 A-AC

Features

 

  • Replacement blade set available with factory-installed spacer guide
  • Quickly cuts door skin off frame
  • Easily attaches to your drill
  • Navigates body lines and corners

Videos

TurboXTools DSR Door Skin Remover Tool

Catalogs

Auto Catalog

Testimonials

Write a Testimonial

Your Name
Rate This Product
Headline
Comment
Captcha

Please enter the text you see in the image with no spaces.



Instructions

TIPS & TRICKS

 

DSR1 and DSR1A Door Skinning TurboXTools

Operate in a well-lighted area to ensure cutting accuracy.

Start at a corner of the door on a flat open service.  Cutting into the middle of an edge and then turning sharply is a challenge, as is starting a cut on a sharply rising or descending profile.  

Set the starting point an eighth of an inch in from the rolled edge of the door skin.  Allow the blade guide stop to keep your cutting distance at an eighth of an inch.  Do not allow the blades to turn into the door.  

Angle the tool slightly to the right and keep the blades’ cutting edges flush to the metal to find the optimum smooth cutting action.  With the inside edge of the door skin facing up, be aware of any upward curve of the door frame perimeter or rising or descending profiles.  Do not overdo cutting angle and keep blade edges flush to metal.  

Keep the eighth-inch trim cut in sight at all times.   Do not allow cut metal curl to interfere with sight line.  Stop, if necessary, to bend curl to right and out of the way or to snap off curl.

If going off track, do not continue cutting to get back on track.  Stop and reset tool at eighth-inch offset before continuing cut.